First of all im new to this forum but will soon settle in

I have the following

WindowsXp Machine ( sp2 .NET 2 )

Xbox360 Arcade ( Lite-On DG-16D2S / lite on 74850c )

Tools

Sata Pci VIA-VT6421A CHIPSET Card
Team Xecuter Connectivity V3 Pro
Team Xecuter Lite-On Probe Addon

I am new to flashing 360 systems. I have flashed my other Hitachi but these process seems alot different!

From what ive read people are using iPrep or Jungleflasher to flash there lite-on.

I have not used Ck3 before and i was following this guide
team-xecuter.com/ck3/l...indows.htm

Thanks for the speedy reply.

My sata card was not picking up ANY drive attatched to it. I cleaned out the PCI slot and put the card back in ( VIA-VT6421A )

It now works and detects my DG-16D2S.

Jungle Flasher can now see the DG-16D2S drive as well.

I am getting the ***WARNING** SERIAL DATA IS BAD.
I have read the FAQ about this and I think it is due to me not settuping up the drive at the start correctly.

My Question is. What order do I switch on the drive Via Ck3. Open the drive and stop ot half way.

When do i press the ModeB button ?

The prob is plugged in and is blue.

Also how new is the Lite-On DG-16dD2S /lite on 74850c Drive ?

Thanks

Read this tutorial first it has everything you need to know step by step. Make sure the drivers for via card are uninstalled and portIO32 installed . The guide shows you how to do this .

To get key power drive on with half open tray . put the probe in r707 hole and press get key/dummy .

Strongly recommend you spoof the dummy info into a spare drive to make sure you have a good dump BEFORE you ERASE the liteon .

Thanks for the speedy reply.

My sata card was not picking up ANY drive attatched to it. I cleaned out the PCI slot and put the card back in ( VIA-VT6421A )

It now works and detects my DG-16D2S.

Jungle Flasher can now see the DG-16D2S drive as well.

I am getting the ***WARNING** SERIAL DATA IS BAD.
I have read the FAQ about this and I think it is due to me not settuping up the drive at the start correctly.

My Question is. What order do I switch on the drive Via Ck3. Open the drive and stop ot half way.

When do i press the ModeB button ?

The prob is plugged in and is blue.

Thanks

power on drive then open jungleflasher then open tray power down push tray in half way power back on the probe the r707 hole click get key

Great! I will try that when I get home. What do I do with the mode B button? And when I first power the ck3 it is red and the probe is blue. When I press the modeb button in the ck3 turns blue. So do I need to press it at any point?

i m not sure but i think thats only for hitachi

correct me if i m wrong

EpicDamo wrote:

Thanks for the speedy reply. My sata card was not picking up ANY drive attatched to it. I cleaned out the PCI slot and put the card back in ( VIA-VT6421A ) It now works and detects my DG-16D2S. Jungle Flasher can now see the DG-16D2S drive as well. I am getting the ***WARNING** SERIAL DATA IS BAD. I have read the FAQ about this and I think it is due to me not settuping up the drive at the start correctly. My Question is. What order do I switch on the drive Via Ck3. Open the drive and stop ot half way. When do i press the ModeB button ? The prob is plugged in and is blue. Thanks

Does your probe show up in properties ? Make sure you have the right comm port selected and drivers are installed for probe .

You dont press mode B for liteon ...read the tutorial mate .

Here is CK3 toolz :
www.4shared.com/file/1..._v124.html

Try using USB for probe .

Epic fail on my part. I havnt installed the Prob drivers!!

Will do 2nite and try again.

Learning experienc for me

Thanks again for helping out!

when you install the usb drivers dont have the usb plugged in

Ok. So install it , Plug it in , then XP will reconise the device.

And alos is the prob needed for the Lite-On DG-16dD2S /lite on 74850c Drive. I have read somewhere that the ck3 is only needed for power.

Will the light on the ck3 turn from red to blue at any point ?

Thanks

EpicDamo wrote:

Ok. So install it , Plug it in , then XP will reconise the device. And alos is the prob needed for the Lite-On DG-16dD2S /lite on 74850c Drive. I have read somewhere that the ck3 is only needed for power. Will the light on the ck3 turn from red to blue at any point ? Thanks

Yes thats how you install drivers sometimes software can ask you to plug in during install .

Probe is ONLY NEEDED for 74850

I dont have a CK3 but from what I understand the CK3 powers the probe so I assume you need to have both plugged in . Go to executor site im sure there are tutorials on how to use their product .